| Type | Hydraulic Motors, 160-800 | Place of Origin | Guangxi, China | Material | Cast iron |
| Flow | 100-125l/min | Pressure | 1-20MPa | Operating principle | Hydraulic oil |
| Construction | Cycloidal-pin wheel | Trait | Small high speed large torque | Torque | 470-1464N*m |
| Speed | 154-620rpm | Output | 22.2-27.7KW |
| d | 35mm |
| Reference Speed Rating (r/min): | 13000 |
| Cage Type: | Steel |
| Clearance: | C3 |
| Seals or Shields: | Single Metal Shield |
| Limiting Speed Rating (r/min): | 9300 |
| Weight: | 0.46 KGS |
| SKU: | 6307zc3-timken |
| Availability: | In Stock |
| Static Load Rating (kN): | 19.2 |
Documented Solution Program iso 492 bearing
| iso 492 bearing cross reference chart | ||||||||
| h | d | S | U | T | B | a | D | |
| 281 | - | 130mm | - | - | - | 69mm | - | 200mm |
| 492 | - | - | - | - | - | 128mm | - | 360mm |
| 15243 | - | 90mm | - | - | - | - | - | 160mm |
| 12240 | 63.5 mm | - | 4.763 mm | - | - | - | - | - |
| 16281 | - | - | - | 27 mm | - | - | - | - |
| 5753 | - | 35mm | - | - | - | - | - | - |
| 15 | - | - | - | - | - | 46mm | - | 180mm |
| din 281 | - | - | - | - | 41.275 mm | 41.275 mm | 32.421 mm | - |
| din 12240 | - | 260mm | - | - | - | 144mm | - | 440mm |
Tolerances
Tolerance classes and the corresponding values for certain tolerance characteristics are specified in ISO 492 (for radial bearings) and ISO 199 (for thrust
ISO 492 - SiS
STANDARD. ISO. 492. Fourth edition. 2002-04-15. Rolling bearings — Radial bearings —. Tolerances. Roulements — Roulements radiaux — Tolérances
8. bearing tolerances - Nsk
ISO 492/199/582 (Accuracies of Rolling Bearings). Tolerances are specified for the following items: Regarding bearing accuracy classes, besides ISO
Bearing Tolerances - NTN Global
running accuracy, are regulated by ISO and JIS B 1514 standards .... Notes 1: JIS B 1514, ISO 492 and 199, and DIN 620 have the same specification level
ISO 492:2002(en), Rolling bearings — Radial bearings
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible
ISO 492:2014 - Rolling bearings -- Radial bearings ... - ISO
ISO 492:2014 specifies dimensional and geometrical characteristics, limit deviations from nominal values, and tolerance values to define the interface (except
8. bearing tolerances - NSK
ISO 492/199/582 (Accuracies of Rolling Bearings). Tolerances are specified for the following items: Regarding bearing accuracy classes, besides ISO
ISO 492 - SAI Global
STANDARD. ISO. 492. Fourth edition. 2002-04-15. Rolling bearings — Radial bearings —. Tolerances. Roulements — Roulements radiaux — Tolérances
ISO 492:2002 - Rolling bearings — Radial bearings ... - ISO
ISO 492 specifies tolerances for boundary dimensions (except chamfer dimensions) and the running accuracy of radial rolling bearings specified in ISO 15, ISO
Bearing Tolerances and Precision Levels | AST Bearings
In almost all cases, these standards are similar to or state equivalency with ISO 492. The table below shows the equivalent tolerance grades for three of the most
ISO 492:2014(en), Rolling bearings — Radial bearings
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the
